PrimeLynx Air

What it covers

Central plant serviced, tested and overhauled — compressors, condensers, evaporators and controls returned to rated performance.

What you get

• Compressor and heat exchanger servicing
• Chiller cleaning and servicing
• Tube cleaning and eddy current coordination
• Performance testing before and after overhaul

What it covers

Air-cooled machines cleaned, checked and tuned so heat rejection holds through peak ambient — the condition under which these units lose capacity first.

What you get

• Condenser coil cleaning and fan section servicing
• Preventive maintenance to a planned schedule
• Corrective maintenance and breakdown attendance

What it covers

Water-cooled plant maintained on both sides of the machine — the refrigerant circuit and the chilled water loop that carries cooling to the building.

What you get

• Condenser and evaporator cleaning
• Chilled water pump maintenance
• Chilled water piping inspection

What it covers

Condition established by measurement rather than assumption — readings taken across the machine, faults traced to cause, and output compared against rated duty.

What you get

• Chiller inspection and diagnosis
• Compressor troubleshooting and repair
• Performance testing and optimization

What it covers

Refrigerant losses found and closed before the circuit is topped up again, with the system proved tight and dry ahead of recharging.

What you get

• Leak detection and repair
• Vacuuming and nitrogen pressure testing
• Refrigerant charging to design weight

What it covers

Towers cleaned, treated and mechanically serviced to protect heat rejection capacity and control water-borne contamination risk.

What you get

• Basin, fill and drift eliminator cleaning
• Fan, gearbox and drive servicing
• Water treatment and hygiene monitoring

What it covers

The water side kept in condition — pump overhaul, valve replacement, strainer cleaning and system balancing across primary and secondary loops.

What you get

• Pump overhaul, alignment and seal replacement
• Valve, actuator and strainer servicing
• Hydronic balancing and pressure testing

What it covers

Compressors changed out under controlled conditions — old unit recovered and removed, replacement set, piped, evacuated and returned to service.

What you get

• Compressor installation and alignment
• Compressor removal and replacement
• Pipework reconnection, pressure testing and recharging

What it covers

Machines stripped, inspected, rebuilt and re-tested rather than discarded, with lubrication and filtration renewed as part of the same intervention.

What you get

• Compressor overhauling and rebuilding
• Compressor oil change and oil separator service
• Filter and drier replacement

What it covers

Windings, insulation and starting components tested to find out whether a compressor failed electrically or was failed by something upstream of it.

What you get

• Compressor electrical testing
• Megger and insulation resistance testing
• Compressor troubleshooting and fault diagnosis

What it covers

Unitary systems supplied, installed and maintained across the formats used in offices, villas, retail units and back-of-house areas.

What you get

• Split and ducted split systems
• Cassette air conditioning units
• Floor standing air conditioning units

What it covers

Self-contained package and rooftop plant installed and serviced where cooling is carried on the roof or an external slab rather than inside the building.

What you get

• Package unit supply, installation and service
• Rooftop unit maintenance
• Seasonal condition and performance checks

What it covers

Variable refrigerant systems installed, charged and configured, with controls set up per zone and serviced through their operating life.

What you get

• Indoor and outdoor unit installation and piping
• Refrigerant charging and leak testing
• Zone control configuration and commissioning

What it covers

Chilled water systems where cooling is generated centrally and delivered through air handling and fan coil equipment distributed across the building.

What you get

• Central chilled water air conditioning
• Air handling units (AHU)
• Fan coil units (FCU)

What it covers

Air handling and fan coil units cleaned, repaired and rebalanced so delivered air volume and quality match what the space was designed for.

What you get

• Coil cleaning and filter replacement
• Drain pan and condensate drain cleaning
• Airflow measurement and rebalancing

What it covers

The rotating assembly maintained as a set — fan, motor, drive and bearings — since a fault in any one of them shows up as lost airflow.

What you get

• Blower and motor service
• Belt replacement and tensioning
• Bearing inspection and replacement

What it covers

The control end of the unit verified — that valves move, actuators respond and sensors report a temperature the system can act on correctly.

What you get

• Valve and actuator checking
• Temperature sensor checking and calibration
• Control response verification

What it covers

Temperature-controlled rooms built, maintained and monitored so the holding temperature is stable, evidenced and recoverable after a door is left open.

What you get

• Cold room and chiller room installation and service
• Freezer rooms and walk-in freezers
• Cold storage facility maintenance

What it covers

Fast pull-down and display equipment serviced to hold its rated cycle, from production blast plant to front-of-house cabinets.

What you get

• Blast freezer and blast chiller service
• Display refrigeration maintenance
• Temperature monitoring and pull-down testing

What it covers

The machinery behind the room — compressors, heat exchangers, metering devices and the pipework connecting them, serviced as one circuit.

What you get

• Refrigeration compressors
• Evaporators and condensers
• Expansion valves
• Refrigerant leak detection and repair

What it covers

Ductwork fabricated, installed, altered and insulated to specification, including modification work in occupied and live buildings.

What you get

• Duct installation and fabrication
• Duct repair and modification
• Thermal and acoustic duct insulation

What it covers

Internal cleaning and leakage testing that recover delivered airflow and remove what has been accumulating inside the distribution system.

What you get

• Duct cleaning and sanitization
• Air leakage inspection and sealing
• Grilles, diffusers and dampers

What it covers

Fresh air, extract and pressurization routes sized, installed and balanced for the space they serve and the code they answer to.

What you get

• Ventilation, extract and pressurization systems
• Fan installation and balancing
• Kitchen and car park ventilation

What it covers

Panels opened, inspected and tested — the switching and protection layer that determines whether plant starts, runs and shuts down safely.

What you get

• Control panel inspection and servicing
• Contactor and relay checking
• Overload protection and breaker inspection

What it covers

The inputs the system makes decisions on, verified end to end so control action follows real conditions rather than a drifted reading.

What you get

• Sensors and thermostats
• Pressure switches
• Control wiring inspection and repair

What it covers

Integration and drive-level work — confirming the plant reports honestly to the building management system and runs at the speed it is being asked for.

What you get

• BMS interface and integration checks
• VFD inspection and parameter review
• Electrical fault troubleshooting

What it covers

Day-to-day operation and upkeep of cooling systems, run by resident or visiting teams working to a defined maintenance regime.

What you get

• Resident or visiting technical teams
• Operating logs and consumption monitoring
• Periodic condition and performance reporting

What it covers

Maintenance cover structured around a visit frequency the equipment and the site actually need, with each attendance evidenced in writing.

What you get

• Monthly HVAC maintenance visits
• Quarterly maintenance visits
• Annual maintenance contract (AMC) cover
• Maintenance reports issued after every visit

What it covers

Scheduled servicing by asset class — filters, coils, belts, refrigerant, controls — carried out on a calendar built around the equipment, not the complaint.

What you get

• Preventive maintenance schedule per asset
• Equipment inspection and task checklists
• Equipment asset list and register
• Consumables and filter replacement tracking

What it covers

Diagnosis and repair when equipment fails, including fault-finding, part replacement and a recorded cause so the same failure can be designed out.

What you get

• Fault diagnosis and root cause notes
• Repair execution and part replacement
• Corrective log entry against the asset

What it covers

Priority attendance and temporary cooling when a critical space cannot wait — spot coolers, temporary chillers and mobilized repair crews.

What you get

• Emergency breakdown support and priority call-out
• Temporary and rental cooling deployment
• Continuity plan for critical spaces

What it covers

Mechanical installation followed by systematic testing, air and water balancing, and performance verification against the design intent.

What you get

• Equipment installation to approved shop drawings
• Air and water balancing records
• Testing, commissioning and handover documentation

What it covers

Equipment set, connected and started by system type, from a single split unit through to central chiller plant on a prepared base.

What you get

• Chiller installation and alignment
• Package unit installation
• Split and VRF system installation

What it covers

Refrigerant pipework fabricated, brazed and proved to standard before any charge is introduced — the stage that decides whether a system leaks in year two.

What you get

• Refrigeration system installation
• Copper piping and brazing
• Pressure testing, vacuuming and refrigerant charging

What it covers

Cooling and ventilation designed around industrial heat loads, dust and shift patterns rather than office comfort conditions.

What you get

• Factory HVAC systems
• Production area cooling
• Concrete plant HVAC

What it covers

Large-volume and equipment-critical spaces conditioned to hold the temperature that stored goods and switchgear need to stay within.

What you get

• Warehouse cooling
• Electrical room cooling
• Control room air conditioning

What it covers

Continuous-duty cooling for spaces and processes where an interruption is measured in downtime or spoiled output, not in discomfort.

What you get

• Server and data room cooling
• Industrial refrigeration
• Process cooling systems